Router-language: Difference between revisions

From Alessandro's Wiki
Line 297: Line 297:
* change the polling time interval
* change the polling time interval
  # chassis poll-time 200
  # chassis poll-time 200
#config te
BR-SSH@coresw1(config)#logging buffered 300
Reload required.  Please write memory and then reload or power cycle.
BR-SSH@coresw1(config)#write memory
Write startup-config done.
BR-SSH@coresw1(config)#end
BR-SSH@coresw1#reload
Are you sure? (enter 'y' or 'n'): y
<pre>

Revision as of 07:20, 26 March 2012

Foundry

enable

  • when logged in, the "enable" command give you the administration rights
  • in this status we can monitor e check configuration.

<syntaxhighlight lang=visualfoxpro > $ enable password...

  1. _

</syntaxhighlight>

  • entering in "edit configuration" mode, you can edit the configuration, live! be very careful

<syntaxhighlight lang=visualfoxpro > config [te] password... (config)# </syntaxhighlight>

  • after making changes, you can check them with this command (because "show config" will give you the configuration saved in memory, not the running one that you just modified.

<syntaxhighlight lang=visualfoxpro > (config)# show running-config [...] </syntaxhighlight>

  • after all your checks, this is the command to save the changes permanently.

<syntaxhighlight lang=visualfoxpro > (config)# write memory

</syntaxhighlight>

  • an option to backup the configuration is to copy it by TFTP to a server.

<syntaxhighlight lang=visualfoxpro >

  1. copy running-config tftp 1.2.3.123 router-config-20122112.txt
#Upload running-config to TFTP server done.

</syntaxhighlight>

show cpu

show cpu <syntaxhighlight lang=visualfoxpro > 31 percent busy, from 3248 sec ago 1 sec avg: 31 percent busy 5 sec avg: 31 percent busy 60 sec avg: 31 percent busy

300 sec avg: 31 percent busy </syntaxhighlight>

  • cpu/process utilizaiton

<syntaxhighlight lang=visualfoxpro >

  1. show process cpu

Process Name ACL ARP BGP DOT1X GVRP ICMP IP L2VLAN OSPF RIP STP VRRP 5Sec(%) 1Min(%) 0.00 0.00 0.01 0.01 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.01 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 5Min(%) 15Min(%) Runtime(ms) 0.00 0.00 0 0.01 0.01 714 0.00 0.00 0 0.00 0.00 0 0.00 0.00 0 0.00 0.00 161 0.00 0.00 229 0.00 0.01 673 0.00 0.00 0 0.00 0.00 9 0.00 0.00 7 0.00 0.00 0 </syntaxhighlight>

port status short

  • show interface brief

<syntaxhighlight lang=visualfoxpro > Port Link State Dupl Speed Trunk Tag Priori MAC Name 1 Up Forward Full 1G None No level0 0012.f286.... 2 Disable None None None None No level0 0012.f286....

Port Link State Dupl Speed Trunk Tag Priori MAC Name ve10 Up N/A N/A N/A None N/A N/A 0012.f286.... </syntaxhighlight>

ip traffic

<syntaxhighlight lang=visualfoxpro >

  1. show ip traffic

IP Statistics

 249333533 received, 92410 sent, 248630753 forwarded
 0 filtered, 0 fragmented, 0 reassembled, 4480 bad header
 495 no route, 0 unknown proto, 0 no buffer, 43582 other errors

ARP Statistics

 151530 total recv, 149155 req recv, 214351 req sent, 67830 rep sent
 0 pending drop, 0 invalid source, 0 invalid dest

ICMP Statistics Received:

 13364 total, 25 errors, 103 unreachable, 25 time exceed
 0 parameter, 0 source quench, 0 redirect, 13202 echo, 
 9 echo reply, 0 timestamp, 0 timestamp reply, 0 addr mask
 0 addr mask reply, 0 irdp advertisement, 0 irdp solicitation

Sent:

 55536 total, 0 errors, 38105 unreachable, 4205 time exceed
 24 parameter, 0 source quench, 0 redirect, 0 echo, 
 13202 echo reply, 0 timestamp, 0 timestamp reply, 0 addr mask
 0 addr mask reply, 0 irdp advertisement, 0 irdp solicitation

UDP Statistics

 173951 received, 15129 sent, 119850 no port, 0 input errors

</syntaxhighlight>

MAC address table

show mac-address

<syntaxhighlight lang=visualfoxpro > Total active entries from all ports = 69 MAC-Address Port Type Index VLAN 0800.270c.ce47 5 Dynamic 30 113 0011.7800.9a44 8 Dynamic 14232 200 </syntaxhighlight>

ethernet data flow statistics

  • show rmon statistics

<syntaxhighlight lang=visualfoxpro > Ethernet statistics 1 is active, owned by monitor

Interface 1 (ifIndex 1) counters
          Octets          62219423556
     Drop events                    0             Packets             74215428
  Broadcast pkts                  613      Multicast pkts                83808
CRC align errors                    0      Undersize pkts                    0
   Oversize pkts                    0           Fragments                    0
         Jabbers                    0          Collisions                    0
Packet size counters
              64              8199939           65 to 127             21283872
      128 to 255              2667477          256 to 511              1406813
     512 to 1023              2001555        1024 to 1518             38655772

</syntaxhighlight>

physical media installed in port

  • show media

<syntaxhighlight lang=visualfoxpro > 1:M-SX 2: 3: 4: 5: C 6: C 7: C 8: C 9: C 10: C 11: C 12: C 13: C 14: C 15: C 16: C 17: C 18: C 19: C 20: C 21: C 22: C 23: C 24: C </syntaxhighlight>

  • C1550 – CWDM transceiver with 1550 nm wavelength
  • EFM-U – 1000Base-BX10-U fiber (uplink) transceiver
  • EFM-D – 1000Base-BX10-D fiber (downlink) transceiver
  • M-FX – 100BaseFX fiber mini-GBIC
  • M-FXB1 or M-FXB2 – 100BaseFX fiber mini-GBIC
  • M-LX – 1000BaseLX fiber mini-GBIC
  • M-SX – 1000BaseSX fiber mini-GBIC
  • M-TX – 1000BaseTX copper mini-GBIC
  • M-XR – 1000BaseSX 2 fiber mini-GBIC
  • FXB1 or FXB2 – 1000BaseBX fiber mini-GBIC
  • M-LHA 1000BaseLHA fiber mini-GBIC

ethernet details

  • show interface ethernet 1

<syntaxhighlight lang=visualfoxpro > GigabitEthernet1 is up, line protocol is up

 Hardware is GigabitEthernet, address is 0012.f286.7e40 (bia 0012.f286.7e40)
 Configured speed auto, actual 1Gbit, configured duplex fdx, actual fdx
 Configured mdi mode AUTO, actual MDI
 Member of L2 VLAN ID 10, port is untagged, port state is FORWARDING
 BPDU guard is Disabled, ROOT protect is Disabled
 Link Error Dampening is Disabled
 STP configured to ON, priority is level0
 Flow Control is config enabled, oper enabled, negotiation disabled
 mirror disabled, monitor disabled
 Not member of any active trunks
 Not member of any configured trunks
 No port name
 IPG MII 96 bits-time, IPG GMII 96 bits-time
 IP MTU 1500 bytes, encapsulation ethernet
 300 second input rate: 262016 bits/sec, 119 packets/sec, 0.02% utilization
 300 second output rate: 1558744 bits/sec, 178 packets/sec, 0.15% utilization
 35819040 packets input, 31760156880 bytes, 0 no buffer
 Received 559 broadcasts, 83280 multicasts, 35735201 unicasts
 0 input errors, 0 CRC, 0 frame, 0 ignored
 0 runts, 0 giants
 38293277 packets output, 30371035971 bytes, 0 underruns
 Transmitted 53 broadcasts, 0 multicasts, 38293224 unicasts
 0 output errors, 0 collisions

</syntaxhighlight>

ip routes

show ip

<syntaxhighlight lang=visualfoxpro > Global Settings

 ttl: 64, arp-age: 10, bootp-relay-max-hops: 4
 router-id : 0.0.0.0
 enabled : UDP-Broadcast-Forwarding  Source-Route  Load-Sharing  RARP  
 disabled: Route-Only  Directed-Broadcast-Forwarding  IRDP  Proxy-ARP  RIP  DVMRP  VRRP  VRRP-Extended  

Static Routes

 Index   IP Address        Subnet Mask       Next Hop Router   Metric Distance
 1       0.0.0.0           0.0.0.0           145.145.24.140    1      1 0
 2       192.168.251.0     255.255.255.0     192.168.252.1     1      1 0

</syntaxhighlight>

ip interface networks

<syntaxhighlight lang=visualfoxpro > show ip interface Interface IP-Address OK? Method Status Protocol Ve 10 1.5.4.1 YES NVRAM up up Ve 100 1.2.1.33 YES NVRAM up up Ve 101 1.2.1.129 YES NVRAM up up Ve 102 1.2.1.193 YES NVRAM up up Ve 103 1.2.1.225 YES NVRAM up up Ve 104 1.2.1.241 YES NVRAM up up Ve 105 1.2.1.249 YES NVRAM up up Ve 106 1.2.1.17 YES NVRAM up up Ve 111 1.2.1.65 YES NVRAM up up Ve 112 1.2.1.81 YES NVRAM up up Ve 113 1.2.1.97 YES NVRAM up up Ve 200 1.2.3.4 YES NVRAM up up </syntaxhighlight>

VLAN detail

  • show vlans

<syntaxhighlight lang=visualfoxpro > Total PORT-VLAN entries: 19 Maximum PORT-VLAN entries: 4095 PORT-VLAN 1, Name DEFAULT-VLAN, Priority level0, Spanning tree Off

Untagged Ports:   2   3   4  19  20 
  Tagged Ports: None
  Uplink Ports: None
DualMode Ports: None

</syntaxhighlight>

virtual ethernet configuration

  • is the ip configuration of the vlan subnet

<syntaxhighlight lang=visualfoxpro >

interface ve 300

port-name v-secondary
ip access-group 300 in
ip address 1.2.1.1 255.255.255.240

! interface ve 100

port-name v-primary
ip address 1.2.3.1 255.255.252.0

</syntaxhighlight>

access list per IP

  • access list used by virtual ethernet

<syntaxhighlight lang=visualfoxpro >

access-list 10 permit 1.2.3.0 0.0.3.255 access-list 10 permit 1.2.1.0 0.0.0.255 access-list 10 deny any log

access-list 300 deny ip any 1.2.3.0 0.0.3.255 log access-list 300 deny ip any 1.2.1.0 0.0.0.255 log access-list 300 permit ip any any

access-list 103 permit ip any 1.2.5.0 0.0.0.255 </syntaxhighlight>

set DNS

  • add 3 DNS servers:

<syntaxhighlight lang=python > ip dns server-address 1.2.3.4 10.11.12.13 101.102.103.104 </syntaxhighlight>

  • del 1 DNS server:

<syntaxhighlight lang=python > no ip dns server-address 10.11.12.13 </syntaxhighlight>

SSH management config

<syntaxhighlight lang=visualfoxpro >

ip ssh  key-authentication no
ip ssh  source-interface ve 200

</syntaxhighlight>

add port to VLAN

<syntaxhighlight lang=visualfoxpro >

  • add tagged port:
# vlan 4
(vlan-4)# tag ethe 11
# end
  • add untagged port
(vlan-4)# untag ethe 11
# end

</syntaxhighlight>

remove port from VLAN

<syntaxhighlight lang=visualfoxpro >

  • remove un-tagged port:
#vlan 4
(vlan-4)# no untag ethe 11
# end
  • tagged port
(vlan-4)# no tag ethe 11
# end

</syntaxhighlight>

change temperature warning level

  • temperature at when the device will give warning
# temperature warning 47
  • temperature at when the device will shut down
# temperature shutdown 57
  • change the polling time interval
# chassis poll-time 200
  1. config te

BR-SSH@coresw1(config)#logging buffered 300 Reload required. Please write memory and then reload or power cycle. BR-SSH@coresw1(config)#write memory Write startup-config done. BR-SSH@coresw1(config)#end BR-SSH@coresw1#reload Are you sure? (enter 'y' or 'n'): y