Router-language
Foundry / Cisco IOS
enable
- when logged in, the "enable" command give you the administration rights
<syntaxhighlight lang=visualfoxpro > $ enable
- config [te]
(config)# (config)# (config)# show running-config (config)# write memory
</syntaxhighlight>
port status short
- show interface brief
<syntaxhighlight lang=visualfoxpro > Port Link State Dupl Speed Trunk Tag Priori MAC Name 1 Up Forward Full 1G None No level0 0012.f286.... 2 Disable None None None None No level0 0012.f286....
Port Link State Dupl Speed Trunk Tag Priori MAC Name ve10 Up N/A N/A N/A None N/A N/A 0012.f286.... </syntaxhighlight>
MAC address table
show mac-address
<syntaxhighlight lang=visualfoxpro > Total active entries from all ports = 69 MAC-Address Port Type Index VLAN 0800.270c.ce47 5 Dynamic 30 113 0011.7800.9a44 8 Dynamic 14232 200 </syntaxhighlight>
ethernet data flow statistics
- show rmon statistics
<syntaxhighlight lang=visualfoxpro > Ethernet statistics 1 is active, owned by monitor
Interface 1 (ifIndex 1) counters
Octets 62219423556
Drop events 0 Packets 74215428
Broadcast pkts 613 Multicast pkts 83808
CRC align errors 0 Undersize pkts 0
Oversize pkts 0 Fragments 0
Jabbers 0 Collisions 0
Packet size counters
64 8199939 65 to 127 21283872
128 to 255 2667477 256 to 511 1406813
512 to 1023 2001555 1024 to 1518 38655772
</syntaxhighlight>
ethernet details
- show interface ethernet 1
<syntaxhighlight lang=visualfoxpro > GigabitEthernet1 is up, line protocol is up
Hardware is GigabitEthernet, address is 0012.f286.7e40 (bia 0012.f286.7e40) Configured speed auto, actual 1Gbit, configured duplex fdx, actual fdx Configured mdi mode AUTO, actual MDI Member of L2 VLAN ID 10, port is untagged, port state is FORWARDING BPDU guard is Disabled, ROOT protect is Disabled Link Error Dampening is Disabled STP configured to ON, priority is level0 Flow Control is config enabled, oper enabled, negotiation disabled mirror disabled, monitor disabled Not member of any active trunks Not member of any configured trunks No port name IPG MII 96 bits-time, IPG GMII 96 bits-time IP MTU 1500 bytes, encapsulation ethernet 300 second input rate: 262016 bits/sec, 119 packets/sec, 0.02% utilization 300 second output rate: 1558744 bits/sec, 178 packets/sec, 0.15% utilization 35819040 packets input, 31760156880 bytes, 0 no buffer Received 559 broadcasts, 83280 multicasts, 35735201 unicasts 0 input errors, 0 CRC, 0 frame, 0 ignored 0 runts, 0 giants 38293277 packets output, 30371035971 bytes, 0 underruns Transmitted 53 broadcasts, 0 multicasts, 38293224 unicasts 0 output errors, 0 collisions
</syntaxhighlight>
ip routes
show ip
<syntaxhighlight lang=visualfoxpro > Global Settings
ttl: 64, arp-age: 10, bootp-relay-max-hops: 4 router-id : 0.0.0.0 enabled : UDP-Broadcast-Forwarding Source-Route Load-Sharing RARP disabled: Route-Only Directed-Broadcast-Forwarding IRDP Proxy-ARP RIP DVMRP VRRP VRRP-Extended
Static Routes
Index IP Address Subnet Mask Next Hop Router Metric Distance 1 0.0.0.0 0.0.0.0 145.145.24.140 1 1 0 2 192.168.251.0 255.255.255.0 192.168.252.1 1 1 0
</syntaxhighlight>
VLAN detail
- show vlans
<syntaxhighlight lang=visualfoxpro > Total PORT-VLAN entries: 19 Maximum PORT-VLAN entries: 4095 PORT-VLAN 1, Name DEFAULT-VLAN, Priority level0, Spanning tree Off
Untagged Ports: 2 3 4 19 20 Tagged Ports: None Uplink Ports: None DualMode Ports: None
</syntaxhighlight>
virtual ethernet configuration
- is the ip configuration of the vlan subnet
<syntaxhighlight lang=visualfoxpro >
interface ve 300
port-name v-secondary ip access-group 300 in ip address 1.2.1.1 255.255.255.240
! interface ve 100
port-name v-primary ip address 1.2.3.1 255.255.252.0
</syntaxhighlight>
access list per IP
- access list used by virtual ethernet
<syntaxhighlight lang=visualfoxpro >
access-list 10 permit 1.2.3.0 0.0.3.255 access-list 10 permit 1.2.1.0 0.0.0.255 access-list 10 deny any log
access-list 300 deny ip any 1.2.3.0 0.0.3.255 log access-list 300 deny ip any 1.2.1.0 0.0.0.255 log access-list 300 permit ip any any
access-list 103 permit ip any 1.2.5.0 0.0.0.255 </syntaxhighlight>
set DNS
- add 3 DNS servers:
<syntaxhighlight lang=python > ip dns server-address 1.2.3.4 10.11.12.13 101.102.103.104 </syntaxhighlight>
- del 1 DNS server:
<syntaxhighlight lang=python > no ip dns server-address 10.11.12.13 </syntaxhighlight>
SSH management config
<syntaxhighlight lang=visualfoxpro >
ip ssh key-authentication no ip ssh source-interface ve 200
</syntaxhighlight>
add port to VLAN
<syntaxhighlight lang=visualfoxpro >
- add tagged port:
# vlan 4 (vlan-4)# tag ethe 11 # end
- add untagged port
(vlan-4)# untag ethe 11 # end
</syntaxhighlight>
remove port from VLAN
<syntaxhighlight lang=visualfoxpro >
- remove un-tagged port:
#vlan 4 (vlan-4)# no untag ethe 11 # end
- tagged port
(vlan-4)# no tag ethe 11 # end
</syntaxhighlight>